Custom Side Gates


Centre opening custom side gates

Centre opening custom side gates

A client wanted custom side gates built for their Art Deco home that would match the style of the original front gates on their property.

The side of the house where the side gates were required was a little wider than normal which would make a single gate too large. Centre opening double side gates were suggested which would have a more pleasing aesthetic. The fence on the side of the house was too flimsy to support a gate so a 100mm square steel pillar needed to be installed to support one side.

Using the original front gates (which we had just restored) as a guide, a suitable design for the side gates was developed which captured the look we were after.

One gate layout

One gate half jigged out ready for welding

Side path before gate installation

Side path before gate installation

Completed gates

Completed gates with a cold gal coating and primed

Back view of gates

Back view of gates

The installation was very straight forward but the house was cement rendered and there was no way of knowing if you were drilling into bricks or mortar so dynabolts would be a bit dicey. Instead it was decided to use Chemset studs which provided a much more secure anchor without putting undue stress on the brickwork.

The installation of the custom side gates has made a nice addition to the overall look of the property.

Front Gate Restoration

Restored front driveway gates

Restored front driveway gates

The owner of this Art Deco home wanted to keep the original front gates so decided on a front gate restoration to bring them back to their original condition. This was easier said than done. Over the years a large Japanese maple tree had pushed one of the driveway gate supports out of square making the front gate impossible to close. In fact the front gates had been left open in a deteriorated state for decades.

We were approached to see if anything could be done to rectify the situation. A small pedestrian gate further along the wall had also fallen victim to the same fate with tree roots moving the brick fence over the years so the gate would not even fit between their supports anymore. The client did not want to demolish and rebuild the fence but wanted to retain the original front gates as much as possible.

The first thing was to remove the gates and return them to the workshop. Firstly they were sent to be sand blasted to remove the old paint and corrosion. Careful measurements were made of the front gate supports to determine how they could be re-hinged. The existing hinges and latches were severely corroded and could not be used so a new hinge and latch arrangement had to be devised.

With the new hinge arrangement the driveway gates had to be cut down approximately 100mm to fit between the support pillars. By cutting 50mm off the hinged side of each gate their symmetry was retained without detracting from their appearance.

Original gate

The original driveway gates were corroded and missing parts

Original pedestrian gate

Original pedestrian gate was in very bad shape

Laser showing gate support lean

Laser level showing gate support lean

New gate installation

Cut down gate with lean compensating hinge layout

Once the lean of the gate pillars had been determined a compensating hinge arrangement was built so the gates would all hang square once again.

New pedestrian gate

New cut down pedestrian gate

New gate latch

New pedestrian gate latch

The pedestrian gate also had to be cut down about 50-60mm as well and missing parts replaced. A new hinge and latch arrangement was devised for it as well. It proved impossible to find a suitable gate latch. The original latches and hinges were no longer available and most gates nowadays fit to the edge of a pillar, not the middle. A new latch setup was built which worked very well without being too obtrusive.

The client also wanted some side gates built for the house using the same design as the existing front gates. These are described in another post.

Concave Table Base

Concave base mirror table

Concave base mirror table

A custom concave table base was required on which a large black framed mirror could be mounted. The client wanted a unique display table for their optometrist business. A sturdy design was developed for the base section that blended well with the mirror while maintaining an elegant double concave surface on the base.

White LEDs around the inside edge of the mirror frame were also fitted to illuminate the display area. The table base was constructed of timber and was finished in a high gloss black enamel.

To make the concave surfaces an intricate timber framework was built on which the plywood surfaces could be attached. To keep the weight to a minimum sections of ply were cut from the ply panel components that were not structurally required. This had the added benefit of allowing access inside the base to ensure good adhesive bonding of the edges of the concave surfaces.

Routing the curved profiles for the support structure

Routing the curved profiles for the support structure

Completed internal framework prior to cladding

Completed internal framework prior to cladding

First concave 5mm bendy ply section attached

First concave ply section attached

Cladding in ply completed

Cladding in 5mm bendy ply completed

The LED strips around the inside edge of the mirror were powered by small battery packs fitted in recesses under the mirror in the base section. The LEDs were divided into two sections with a battery pack fitted either end of the table base.

Side view of concave table in shop

Side view of concave table in shop

View of the mirror top showing LED strips

View of the mirror top showing LED strips

Giant Sized Music Box

Giant sized music box

Giant sized music box

This giant sized music box was built for a client who wanted an adult ballet dancer to perform a short routine for an event. An old fashioned look was required so a convex sided box with timber trim top and bottom was decided upon with floral decals on the side. A giant sized silver key was also built that fitted into the top of the music box to give the illusion of being able to “wind it up”.

The most complex part of the giant sized music box build was constructing the convex middle section. A timber skeleton was built with curved inner support panels on which bendy ply could be attached. After the first two opposite sides were attached the curve of the remaining sides were carefully traced using the exposed inner panels as a guide. The sides were then trimmed to almost the line and then sanded to the final shape by hand. This was accomplished by glueing sandpaper around a length of 30mm tube which was then drawn back and forth following the curve of the inner panels. It was important to get the outer curve of the sides to match exactly the inner support panel curve so that the bendy ply would contact all four surfaces when folded over them. This ensured a neat join of the side panels once they were sanded back.

First two sides attached

First two sides attached to the inner framework

Marking the side curve

Marking the cutting line for the side curve

Sanding the side panels

Sanding the side panels to match the curve

Side panels sanded

First two sides sanded and ready for last two side panels


Once the music box middle panels had been sanded to match the curve of the sides the remaining two sides were attached. Liquid nails was used along all internal faces and the edges of the first two side panels. Once attached the adhesive was spread evenly along the inside join of the sides to ensure a good bond. The weight reducing holes in the inner framework facilitated access to these areas.

Next the music box base and top were built. These were quite straightforward to build and the top used 30mm thick pine that would support the dancer. Timber mouldings were cut to make the music box look more interesting and small cabriole legs were purchased to add that bit of old fashioned charm.

Music base unit

Music box base section

Glueing the top section

Glueing the top section


The music box parts were then undercoated and painted. Floral decals printed on stick-on vinyl were attached to the middle section after the final painting had been done. A final over spray of matt clear polyurethane blended the decal and the topcoat of the music box and also added a bit more adhesion for the decals around their edges.

Attaching floral decals

Floral decals are attached to the middle section

Assembled music box

Assembled sections ready for final clear coat

Giant ballerina music box
Music box with Ballerina